The Conference Proceedings will be internationally distributed by AACE and will be available both in hard copy book and online.
Attendees who want to receive a hard copy proceedings book on-site must order the book prior to the conference. All books not ordered prior to the conference will be shipped following the conference.
Examples for each area can be found by clicking on the links below (e.g. Title, Abstract, Acknowledgements, Running Text, etc...). To see an example of a complete paper, click here (Adobe Acrobat format).
|Presentation Category||Maximum Length(inc. graphics & references)|
|Keynote/Invited Speakers:||15 pages|
|Full Papers:||10 pages, minimum 7 pages|
|Brief Papers:||6 pages|
|Best Practices Session:||6 pages|
|Showcase: Research/Technical||6 pages|
|Showcase: Products/Services||6 pages|
|Corporate Demos & Showcases:||150 words (to be published only in Abstracts Book)|
|Symposia:||Abstract only for the Symposium introduction; each paper presenting in a Symposium should follow the Brief Paper length guide; these papers should be submitted separately after acceptance of the Symposium. Individual paper submission instructions will be emailed after acceptance.|
|Virtual Brief Papers||6 pages|
|Virtual Posters/Demos||6 pages|
|Virtual Corporate Presentations||150 words (to be published only in Abstracts Book)|
Text Area - 16.51 cm x 22.86 cm or 6 1/2 x 9 inches
Begin the Text Area 1" or 2.54 cm from top of hard copy page. Use only a one-column layout. Set your margins so that they precisely match the text area specified. Place pictures, figures and tables centered between the margins without any text flowing around them. Do not start a new page for new sections (chapters) or subsections. Do not insert page numbers. Also notice that no form of running heads is allowed.
Do not use the paragraph spacing feature of your word processor to create the line spaces indicated in the following sections.
The title of a paper consists of the title itself, capitalized (all words except for short connectives should start with a capital letter), unnumbered and centered between the margins. Use a serif typeface (e.g. Times or Times New Roman), 14 point, bold font for the title. There should be no title page. The body of the paper should begin immediately after the title and author text.
Leave 2 blank lines after title and then give the name and affiliation of each author including department, institution, country, and email address centered between margins. Multiple authors should be delimited by a single blank line. Use a serif typeface (e.g. Times), 10 point. Leave at least three blank lines after the last author. Please do not put any acknowledgements or thanks here, but place them in the optional Acknowledgement section at the end of the document.
Abstracts should be 75-150 words in length. Indent 2 cm or 3/4" from left and right margins for abstract. Skip 2 lines before and after abstract. Start the abstract with the sequence "Abstract:" (without the quotes) in 9 point bold-face without a line break after "Abstract:".
Start the literature references with the first level header "References" (see Headings below for a detailed description of the first level header format).
This is an optional section. Acknowledgements or appreciation to individuals for assistance with the manuscript or with the material reported should be included and appear at the end of the article after References. Financial support for work reported or a grant under which a study was made should be noted in the Acknowledgements. Start the acknowledgements section with the sequence "Acknowledgements" in 10 point bold-face, left justified, followed by a single blank line.
Use a typeface with serifs for all levels of headings. It is recommended to use Times or Times New Roman. Leave sufficient place for the title to stand out clearly. Leave 2 lines blank above and 1 line below the headings. If a heading is directly followed by a lower level heading the 2 blank lines before the lower level heading should be omitted. All headings should be capitalized (i.e. all words except for short connectives should have a capital initial). The title should be centered between the margins, all lower level headings should be left-justified.
Use a typeface with serifs for running text. It is recommended to use Times or New Times Roman. Use 10-point type size and one line spacing for normal text and 9-point type size for small text (abstract, literature references and acknowledgements). Use italic print to emphasize words. Note: bold type and underlining should be avoided. The text should always be justified to occupy the full line width, so that the right margin is not ragged. All text should be single-spaced.
For Computer programs both sans-serif and serif typefaces are allowed. Use 10-point type size and one line spacing.
Insert the sequence "(Name year)" (without the quotes) into the running text for a citation to a literature reference. Name is the second name of the author and year is the year of printing. Also a citation to several authors is allowed. In this case the single authors must be delimited either by commas or the word "&". The phrase "et al." is also valid. The year can either be written in short form or in long form (i.e. 92 and 1992 are both valid entries) is a possible lower case literal, if you refer to more than one article of an author of the same year. The word "see" and the brackets around the year are optional.
Insert the sequence "(Fig. n)" (without the quotes) into the running text to refer to a Figure contained in the current document.
Insert the sequence "(Tab. n)" (without the quotes) into the running text for a markup to a table contained in the current document.
For a reference to a footnote, use the form [n], where n is the unique number of the footnote [see Footnotes]. Please note that footnotes should only be used when unavoidable.
Please use exactly the format given here to allow us to insert Hypertext links automatically by searching for these special sequences.
Every Reference must start with the sequence "Name (Year)" (without the quotes). Name and year must match the citation in the running text [see Citations]. The single information fields of a Reference (Author1, Author2, Title...) should be divided by commas or semicolons.
Use the following APA style when referencing a book or journal article making sure to precede the reference with the bracketed information described above:
Center figures and tables between the margins with one blank line above and below each. Insert the text "Figure n: description" or "Table n: description" (without the quotes) in 10 point font after the figure/table (n is a unique number that identifies the figure/table; description is a short description about its contents. "Figure n: and Table n:" should be in bold). Please use an expressive description for your figures to allow finding them in a keyword search.
Separate footnotes from the preceding main text by a line from the left to the center of the page. Start the footnote with the sequence "[n]", where n is the unique number of that footnote (unique means that this number can only appear once on a page, not throughout the whole document). Use a 9 point font for footnote text.
 as we mentioned earlier this is how to write footnotes
A format which best preserves the "document's look" as it was submitted is preferred. You should not have problems generating a file in one of those formats, no matter which word processor you are using. When submitting a file, please follow the rules given below which will allow your paper to be read and converted. To provide an interface to a wide variety of word processors, we accept the following file types:
To submit your Proceedings file, you must be using a Java-enabled browser and it must support file uploads. Most up-to-date browsers support these features.